How To Remove Dent From Car? 11 Easiest Ways

Dent is a mishap problem in most cars, especially it is a little bit difficult to remove a dent from a care sheet.  In this article, we will share with you tips and tricks which will help you to remove the dent from your car as well as you can get information on how to remove dent from car with cold plastic and hot plastic. Let’s check it now.

How To Remove Dent From Car?

Car dents are a common occurrence, especially on older cars. But there is no need to panic if you find a dent in your car. You can remove these dents from your vehicle without spending a lot of money or taking it to the repair shop.

Here are some do-it-yourself methods for removing dents from your car:

Use A Plunger

use a plunger to fix a dent

When you need to pull a dent out of a car, your first thought might be to grab a hammer and start pounding away. But not so fast! You can actually damage your paint if you use the wrong technique or tool. Instead, use a plunger-type device that pulls out dents by suction. The suction will pull the metal back into place while minimizing any damage to the surrounding area.

Use Boiling Water

Car dent removal hot water

You can also use boiling water to help remove dents from your car. Just pour boiling water over the dent and let it sit for 5 minutes before wiping off the excess water with a towel or rag (be careful!). As the metal cools down, it should return to its original shape. If not, repeat this process until the dent pops out completely on its own without any help from you!

Use A Hair Dryer & Compressed Air

Car dent removal Hair Dryer

If you have a tiny dent in your car, then this method might work for you. First, blow hot air from the hair dryer onto the dent for about 10 seconds. Next, use compressed air from an aerosol can spray nozzle or compressor to blow away any moisture that may have collected on the surface of your car.

Use Dry Ice

You can also use dry ice to help loosen up the dent and make it easier for you to pop out. You should use gloves when handling dry ice since it is extremely cold and could cause burns if you touch it directly with your hands or skin.

Use A Vacuum Cleaner & Pot

If you have a dent in your car’s finish and don’t want to spend the money on getting it fixed by a professional, there are a few things that you can do at home. One of them is using a vacuum cleaner and pot. The idea behind this method is that if you apply enough heat and pressure on the surface of the metal, it will pop back into place.

To do this, simply lay down a thick towel on top of the dent and apply pressure with your hand or foot while heating up the surface with a heat gun or blow dryer. You’ll know if it worked when you no longer feel any resistance when trying to push out the dent.

Use Hot Glue, Wooden Dowels, & Screws

If the dent is small enough, you can use hot glue to fill it in. Use a toothpick or wooden dowel to apply the glue evenly over the dent. Wait for it to dry completely before proceeding with any other steps. If there is excess glue on top of the dent itself, use sandpaper or an emery board to smooth it out after it dries.

Use A Long Metal Rod & Knockdown

Car dent removal long metal rod

Using a long metal rod with a hook at one end is the easiest way to remove small dings from your car’s bodywork. The hook makes it easy to grab onto the edge of the dent and pull it out without damaging any other part of your paint job.

Use A Specialty Tool

If you don’t have a long metal rod on hand, you can use a specialty tool called a knockdown hammer. This works in much the same way as using a long metal rod but is easier to control because it has an adjustable handle that allows you to adjust its length depending on how big of an area needs fixing. You should be able to find these tools at any auto parts store near your location or online if there isn’t one nearby.

Do-it-Yourself Dent Repair ( DIY Method)

The most common way to repair dents and dings on your car is by using a hammer and dolly set. These tools can help you pop the dent out of place by forcing it back into its original shape. You’ll want to start with the hammer and dolly on opposite sides of the dent so you can push it out from both sides at once. Keep working until the metal has returned to its original shape, then put some primer paint on top of the metal to prevent rusting.

Hammer It Back In Place

You can also use a rubber mallet or plastic hammer if you don’t have access to a dolly set. With these tools, you’ll need to hammer down into the edge of the dent until it pops back into place. When working with a rubber mallet or plastic bumpers, make sure that you don’t hit too hard, or else you could cause more damage than good!

Release The Dent With Compressed Air And A Hairdryer

If the dent is small enough, then using compressed air and a hair dryer could be all that’s needed. Use the hair dryer on low heat to warm up the area around where the dent is located and then use compressed air to push out any excess moisture from inside of it. Once this has been done, smooth out any rough edges with a putty knife or similar tool until everything looks even again.

Use A Rubber Hammer

If you don’t have any experience with auto body work, use a rubber hammer instead of a metal one because it won’t damage your car’s paint job or scratch its surface. You can find these hammers at any auto parts store or hardware store near you. Apply pressure on the dent with this tool until it pops out completely from your car’s body.

FAQs

Will Boiling Water Damage Car Paint?

A lot of people have been asking this question recently, and the answer is yes. Boiling water can damage your car’s paint job. Boiling water is hot enough to melt some metals, including aluminum and zinc – two components of some car paints. If you were to pour boiling water on your car’s hood, it would be more than enough to damage its finish.

This doesn’t mean that if you get a little bit of hot water on your paint job, it will instantly start bubbling or melting off. It’s unlikely that any amount of boiling water will cause any permanent damage unless it drips onto a particular area for an extended period of time (or if the paint is extremely thin).

You might think that because you’re using cold water instead of boiling water, there’s no way it could cause any damage – but that actually isn’t true either! Cold water can cause damage as well if left on long enough (not just a few seconds or minutes like with boiling water).

Do Dent Pullers Work?

Dent pullers work by pulling the metal out of the dent. The puller first attaches to the back of the dent and then pulls out the damaged area. Dent pullers come in different sizes and shapes, so you can use them on any type of car or truck.

Dent pullers are made from hardened steel and coated with chrome to prevent rusting. Dent pullers are very easy to use; simply attach one side of the tool to the backside of your car’s fender or door panel, then pull out the dent from inside your car’s interior. The tool will only work if there is enough space between your body panel and your car’s paint job for it to fit inside, so check before purchasing one.

Can Hot Water Pop Out A Dent?

Hot water is often used to remove dents from cars and other vehicles. The idea is that the heat will soften the metal, making it easier to pull out the dent.

Hot water can work for small dents, but it’s not as effective as cold water. The reason is that hot water simply isn’t hot enough to create a significant amount of steam. Steam is what makes a dent pop out.

So if you’re planning on using hot water, you’ll have to be patient. It may take some time before you see any results at all.

Conclusion

Dent removal is one of the classic car fixes, along with changing your oil, putting in new brakes and tires, and doing a good-looking paint job. We hope this article has given you an idea about how to remove dent from car.  If you have any further queries about dent removal, you can freely ask through the comment section given below.

Leave a Comment